Why won't my Southern Pride smoker ignite?

If your Southern Pride smoker will not ignite, check these in order: (1) Verify gas supply is on and pressure is adequate (Natural gas: 4.5" W.C. minimum; LP: 11.0" W.C. minimum). (2) Inspect the igniter electrode for cracks or carbon buildup — clean or replace the igniter (Part# 582011 for natural gas, Part# 582015 for LP). (3) Check the ignition control module (Part# 582019) — listen for clicking. (4) Inspect the igniter high voltage lead wire (Part# 582012) for damage. (5) Check the 120v to 24v transformer (Part# 582005). For persistent ignition failures, call free tech support at (409) 886-8626.

Why is my Southern Pride smoker's convection fan not working?

A failed convection fan is typically caused by a failed motor, seized bearings, or a tripped circuit breaker. First, check the circuit breaker panel for a tripped breaker on the smoker circuit. Next, listen for the motor — if you hear humming but no rotation, the capacitor (Part# 351012) may have failed. If the motor is completely silent, the convection motor (Part# 522004) may need replacement. Check the fan blade (Part# 532004 or 532011 depending on model) for obstruction. Do not operate the smoker with a non-functioning convection fan — it will cause uneven temperatures and potential overheating.

Why is there excessive smoke coming from my Southern Pride smoker doors?

Excessive smoke escaping from smoker doors indicates worn or damaged door gaskets that no longer create an airtight seal. Inspect gaskets for hardening, cracking, or compression set — gaskets should be pliable and resilient. Also check the door hinge (Part# 870003) and door latch (Part# 771001) alignment — a misaligned door creates gaps. In some cases, the door frame itself may have warped from heat stress. Replace gaskets first (Part# 070001 or 070002) as they are the most common cause and least expensive fix.

What does it mean when my Southern Pride thermostat shows an error code?

Southern Pride digital thermostats display error codes when the thermocouple reads out of range. An "E1" or temperature sensor error typically means the thermocouple (Part# 435001) has failed and needs replacement — this is a common wear item. If the display shows a temperature far above or below the set point, the thermostat control board itself (Part# 432001) may need replacement. For Cook & Hold models (Part# 431020), consult the specific C&H troubleshooting guide in your owner's manual. Call (409) 886-8626 for diagnostic support.

Why is my Southern Pride rotisserie drive system not rotating?

If the rotisserie is not turning, check these components in order: (1) The 4-amp circuit breaker (Part# 442006) for the drive system — it protects against overload and may have tripped. (2) The shock relay breaker (Part# 442011) which trips if racks are overloaded. (3) The gearmotor (Part# 351001 or 351004 depending on model) for failure — gearmotors typically last 5-10 years with proper lubrication. (4) Drive chain tension — a loose chain will slip off sprockets. (5) Rotisserie wheel bearings (Part# 332001 or 333001) for seizure. Never run product on a non-rotating rotisserie.

Troubleshooting

October 19, 2023

Test Rotisserie Advance Button

TF Tommy FontenotOwner and Founder, Tommy's Food Service25+ years in commercial BBQ equipment distribution. Author...

Read Article →

September 20, 2023

Chain Drive Rotisserie Not Working | Diagnostic Process

Learn how to diagnose and fix common chain drive rotisserie problems with our step-by-step troubleshooting guide. Get...

Read Article →

September 20, 2023

Replacing old thermostat 1006 with new digital thermostat 432001

Upgrade your commercial BBQ with our step-by-step guide to replacing old thermostat 1006 with the new digital thermos...

Read Article →

September 20, 2023

Diagnose No Power To CV Thermostat

Learn how to troubleshoot and fix no power issues with your commercial convection oven thermostat. Step-by-step diagn...

Read Article →

September 20, 2023

Smoker w/ CV Thermostat | Smoker Will Not Turn Off

Learn why your commercial smoker with CV thermostat won't turn off. Troubleshoot common issues, check wiring connecti...

Read Article →

September 20, 2023

Digital Cook & Hold Digital Thermostat Programming Instructions

CONTROL OPERATING INSTRUCTIONS 1. The product loading doors must be closed. 2. The control should be in the “IDLE”...

Read Article →

September 20, 2023

What does the "B Fail" Error Mean?

Learn what the B Fail error means on your commercial BBQ equipment, common causes like faulty temperature sensors or ...

Read Article →

September 20, 2023

Burner BTU, Orifice, and Pressure Guide

Learn how BTU ratings, orifice sizes, and gas pressure work together in commercial BBQ equipment. Essential guide for...

Read Article →

September 20, 2023

What should your flame look like?

What Should Your Flame Look Like? Understanding Proper Burner Flame Appearance for NAT and LP Gas Systems One of th...

Read Article →

September 20, 2023

How To Install Mobile Rack Pins & Clips

Learn how to properly install mobile rack pins and clips for your commercial BBQ equipment. Step-by-step guide ensure...

Read Article →