Why won't my Southern Pride smoker ignite?

If your Southern Pride smoker will not ignite, check these in order: (1) Verify gas supply is on and pressure is adequate (Natural gas: 4.5" W.C. minimum; LP: 11.0" W.C. minimum). (2) Inspect the igniter electrode for cracks or carbon buildup — clean or replace the igniter (Part# 582011 for natural gas, Part# 582015 for LP). (3) Check the ignition control module (Part# 582019) — listen for clicking. (4) Inspect the igniter high voltage lead wire (Part# 582012) for damage. (5) Check the 120v to 24v transformer (Part# 582005). For persistent ignition failures, call free tech support at (409) 886-8626.

Why is my Southern Pride smoker's convection fan not working?

A failed convection fan is typically caused by a failed motor, seized bearings, or a tripped circuit breaker. First, check the circuit breaker panel for a tripped breaker on the smoker circuit. Next, listen for the motor — if you hear humming but no rotation, the capacitor (Part# 351012) may have failed. If the motor is completely silent, the convection motor (Part# 522004) may need replacement. Check the fan blade (Part# 532004 or 532011 depending on model) for obstruction. Do not operate the smoker with a non-functioning convection fan — it will cause uneven temperatures and potential overheating.

Why is there excessive smoke coming from my Southern Pride smoker doors?

Excessive smoke escaping from smoker doors indicates worn or damaged door gaskets that no longer create an airtight seal. Inspect gaskets for hardening, cracking, or compression set — gaskets should be pliable and resilient. Also check the door hinge (Part# 870003) and door latch (Part# 771001) alignment — a misaligned door creates gaps. In some cases, the door frame itself may have warped from heat stress. Replace gaskets first (Part# 070001 or 070002) as they are the most common cause and least expensive fix.

What does it mean when my Southern Pride thermostat shows an error code?

Southern Pride digital thermostats display error codes when the thermocouple reads out of range. An "E1" or temperature sensor error typically means the thermocouple (Part# 435001) has failed and needs replacement — this is a common wear item. If the display shows a temperature far above or below the set point, the thermostat control board itself (Part# 432001) may need replacement. For Cook & Hold models (Part# 431020), consult the specific C&H troubleshooting guide in your owner's manual. Call (409) 886-8626 for diagnostic support.

Why is my Southern Pride rotisserie drive system not rotating?

If the rotisserie is not turning, check these components in order: (1) The 4-amp circuit breaker (Part# 442006) for the drive system — it protects against overload and may have tripped. (2) The shock relay breaker (Part# 442011) which trips if racks are overloaded. (3) The gearmotor (Part# 351001 or 351004 depending on model) for failure — gearmotors typically last 5-10 years with proper lubrication. (4) Drive chain tension — a loose chain will slip off sprockets. (5) Rotisserie wheel bearings (Part# 332001 or 333001) for seizure. Never run product on a non-rotating rotisserie.

Troubleshooting

February 19, 2026

Is my foot pedal faulty?

Troubleshoot common commercial BBQ foot pedal issues with our expert guide. Learn diagnostic steps, repair tips, and ...

Read Article →

August 27, 2025

Southern Pride Smoker | No Power To Burner Diagnostic Procedure

NOTICE All repairs should be performed by a certified technician. Southern Pride of Texas® is not liable for any dama...

Read Article →

February 18, 2025

501011 2" Thermometer Indicator Reset Instructions

Below document provides instructions to reset the indicator on a 501001 Southern Pride mechanical thermostat � �

Read Article →

December 04, 2024

CV Thermostat Error Codes

CV Temperature Control/ Thermometer�� Set Up Sheet�� 10/10/07sb � Correct Settings CAL = -5� / TC =...

Read Article →

November 13, 2024

Replacing K Series Smoke Black Door Handle w/ Chrome Ends With Door Handle 871007

When replacing the black door handle w/ chrome ends on an old style K series smoker the new door handles use screws s...

Read Article →

October 30, 2024

Cook & Hold Thermostat Error Messages

Troubleshoot common cook and hold thermostat error messages with our expert guide. Learn quick fixes for temperature ...

Read Article →

October 25, 2024

Southern Pride 582019 Burner Ignition Control Spark Module LED Light Codes

When it comes to your Southern Pride smoker, understanding the meaning behind the burner ignition control module ligh...

Read Article →

October 21, 2024

Vibrating convection motor? Don't forget to check your motor bushings!

If you have a vibrating convection motor just replacing the fan blade may not resolve your issue completely. Check th...

Read Article →

August 15, 2024

Replacing Lesson Convection Motor Rubber Shaft Bushing

If your convection fan motor is shaking badly you either have a dirty fan blade, faulty rubber bushing, or bad motor ...

Read Article →

May 14, 2024

Wall Plug or Breaker Box Trip When Open Doors

If your GFCI or breaker box breaker are tripping when you open up the meat doors of your smoker you likely are having...

Read Article →

February 15, 2024

Mechanical Thermostat Rotisserie Only Working With Foot Pedal

If you're Southern Pride smoker with a mechanical thermostat is working fine except the rotisserie will not�work exce...

Read Article →

January 29, 2024

Old Style Smoke Extractor Linkage System Configuration

Learn how to properly configure old style smoke extractor linkage systems for commercial BBQ equipment. Expert tips o...

Read Article →