Why won't my Southern Pride smoker ignite?

If your Southern Pride smoker will not ignite, check these in order: (1) Verify gas supply is on and pressure is adequate (Natural gas: 4.5" W.C. minimum; LP: 11.0" W.C. minimum). (2) Inspect the igniter electrode for cracks or carbon buildup — clean or replace the igniter (Part# 582011 for natural gas, Part# 582015 for LP). (3) Check the ignition control module (Part# 582019) — listen for clicking. (4) Inspect the igniter high voltage lead wire (Part# 582012) for damage. (5) Check the 120v to 24v transformer (Part# 582005). For persistent ignition failures, call free tech support at (409) 886-8626.

Why is my Southern Pride smoker's convection fan not working?

A failed convection fan is typically caused by a failed motor, seized bearings, or a tripped circuit breaker. First, check the circuit breaker panel for a tripped breaker on the smoker circuit. Next, listen for the motor — if you hear humming but no rotation, the capacitor (Part# 351012) may have failed. If the motor is completely silent, the convection motor (Part# 522004) may need replacement. Check the fan blade (Part# 532004 or 532011 depending on model) for obstruction. Do not operate the smoker with a non-functioning convection fan — it will cause uneven temperatures and potential overheating.

Why is there excessive smoke coming from my Southern Pride smoker doors?

Excessive smoke escaping from smoker doors indicates worn or damaged door gaskets that no longer create an airtight seal. Inspect gaskets for hardening, cracking, or compression set — gaskets should be pliable and resilient. Also check the door hinge (Part# 870003) and door latch (Part# 771001) alignment — a misaligned door creates gaps. In some cases, the door frame itself may have warped from heat stress. Replace gaskets first (Part# 070001 or 070002) as they are the most common cause and least expensive fix.

What does it mean when my Southern Pride thermostat shows an error code?

Southern Pride digital thermostats display error codes when the thermocouple reads out of range. An "E1" or temperature sensor error typically means the thermocouple (Part# 435001) has failed and needs replacement — this is a common wear item. If the display shows a temperature far above or below the set point, the thermostat control board itself (Part# 432001) may need replacement. For Cook & Hold models (Part# 431020), consult the specific C&H troubleshooting guide in your owner's manual. Call (409) 886-8626 for diagnostic support.

Why is my Southern Pride rotisserie drive system not rotating?

If the rotisserie is not turning, check these components in order: (1) The 4-amp circuit breaker (Part# 442006) for the drive system — it protects against overload and may have tripped. (2) The shock relay breaker (Part# 442011) which trips if racks are overloaded. (3) The gearmotor (Part# 351001 or 351004 depending on model) for failure — gearmotors typically last 5-10 years with proper lubrication. (4) Drive chain tension — a loose chain will slip off sprockets. (5) Rotisserie wheel bearings (Part# 332001 or 333001) for seizure. Never run product on a non-rotating rotisserie.

Troubleshooting

August 27, 2025

Southern Pride Smoker | No Power To Burner Diagnostic Procedure

NOTICE All repairs should be performed by a certified technician. Southern Pride of Texas® is not liable for any dama...

Read Article →

October 30, 2024

Cook & Hold Thermostat Error Messages

Troubleshoot common cook and hold thermostat error messages with our expert guide. Learn quick fixes for temperature ...

Read Article →

October 25, 2024

Southern Pride 582019 Burner Ignition Control Spark Module LED Light Codes

When it comes to your Southern Pride smoker, understanding the meaning behind the burner ignition control module ligh...

Read Article →

October 21, 2024

Vibrating convection motor? Don't forget to check your motor bushings!

If you have a vibrating convection motor just replacing the fan blade may not resolve your issue completely. Check th...

Read Article →

August 15, 2024

Replacing Lesson Convection Motor Rubber Shaft Bushing

If your convection fan motor is shaking badly you either have a dirty fan blade, faulty rubber bushing, or bad motor ...

Read Article →

May 14, 2024

Wall Plug or Breaker Box Trip When Open Doors

If your GFCI or breaker box breaker are tripping when you open up the meat doors of your smoker you likely are having...

Read Article →

January 18, 2024

Reverse Drive Motor or Gearmotor Direction

This must be done for mirror image units to make the drive run the correct direction. Chain Driven System: On gearmot...

Read Article →

November 30, 2023

Test Flame Sensor On Burner Control Module

Want to test if your flame sensor is flame sensing on your Southern Pride gas smoker? To check if your ignition elect...

Read Article →

November 27, 2023

Firebox Removal

Learn step-by-step firebox removal techniques for commercial BBQ equipment. Essential maintenance tips to extend smok...

Read Article →

November 27, 2023

Chain Sag

Learn how to identify, prevent, and fix chain sag in commercial BBQ equipment. Expert tips for maintaining proper cha...

Read Article →

November 07, 2023

Rottiserie, Burner, Convection Do NOT Stop With Doors Opened

Learn why keeping commercial BBQ equipment doors closed is crucial for food safety, energy efficiency, and optimal co...

Read Article →

October 19, 2023

Test Rotisserie Advance Button

To test for a faulty rotisserie advance button test for 120v across the N/O block on the back of the switch. When you...

Read Article →